I have replaced motherboards and kept the hard drive many times over the years without any problems.
Well, one "minor" problem with an easy workaround. The first time you boot to Windows (assuming this is a Windows system, given the references to "C:" and "D:"), it will probably detect new hardware and will want to install new drivers off the Windows CD. Unfortunately, I have had motherboard upgrades where this "insert the Windows CD" prompt occurs _before_ the CD drivers are loaded, causing a nice Catch 22 situation.
To get around this, I make a "\windows.cd" directory on the hard drive, and copy the Windows install CD there _before_ installing the new motherboard. Then, simply tell the new hardware wizard to look there, rather than the CD drive itself.
Posted by: Ken at October 19, 2006 7:23 AM
Well, some days before I have read something about copying windows registry, specially "\...\WAB", and "\system32" directory. After that I supposed was told to get some "merge program", and run it including these two situations. The issue was making ourselves a new computer and tranfer the windows serial to the new one, including hard disks and keep them ok. Might be good discoussing these options ? Something good to keep from this?
Vic
Posted by: Vic at October 22, 2006 7:20 PM
I've got a client that has had their mobo and cpu fried, so ive replaced both those, but here is where the problem lies, they did not back up their system and would like to keep everything the way it was on the old hdd without reformatting and losing all data and programs installed (as they do not have the original install files for these programs). My question is (as i know the old xp pro hdd will not boot with new system) i've already run the repair install and recovery console, but to no avail, it gets stuck un the boot loop like many others. But, i have built my own machine with the same system (mobo and cpu) with a clean xp pro install which does not have any programs or devices installed.... could i swap the start up files to the old hdd with the same mobo and cpu to get it started to detect all the new drivers and keep programs and data etc. and if so, what files would i need to replace on the old hdd from my clean hdd? (ive already tried everything i can think of and this popped into mind) btw, i cannot boot into safe mode on the old hdd to remove the drivers so windows will pick them up on repair for the new mobo. and the system when boots in safe mode will hang on 'gagp30kx.sys' which i assume is the video card? or failing that, how would i go about deleting the drivers that try to boot using recovery console. sorry for the long question, im just at that stage where ive been over and over with this thing for days and becoming a zombie. cheers and thanks in advance, pammii.
Posted by: pammii at October 31, 2006 5:42 PM
Linux. Many distributions available, free for the price of downloading and burning it.
I swapped a SATA HD and Grafx card into a fully functional system. Windows would not go. Linux go'ed. Writing this while hunting down a way to make Windows go (for one game only, once I'm done with it I reformat and say goodbye to Windows on my personal boxes).
Why is it so easy to--and get this, hot plug a hard drive into your mobo--change hardware on other OSs while the leading OS supplier's software costs so many man-hours to change? Motherboards' lifespans are finite--not that they die, always, but c'mon, the technology changes.
Posted by: Skandi Franksen at November 3, 2006 8:45 PM
Hi Leo, My, Motherboard has failed me, and I have important data on my HDD(which has windowsxp installed), when I put it in another computer, it just makes a blinking sound and I get the message 'Cannot read HDD'. Is there anything I can do to use this HDD again?
Posted by: dave at November 8, 2006 4:21 AM
A local competent builder is assembling a new machine for me. New: motherboard; new boxed version XPpro; new HD. Old: XPpro; 2 HD; several Autocad,Catia & Solidworks programs. How to transfer to the new machine? I realize this is already partially answered in your column but the "devil" is in the details! Specific questions are best when all details are given. Some friends advise Magic Mover. That seems to out of date. I am in no hurry to lose programs. This seems to be a common task, as 2 other of this builder's customer's are attempting to do the same task. Also I have no agreement on partitioning of the new HD. How many partitions of what size? I have about 20 gig of cad type programs now.
Posted by: arlie at July 2, 2007 10:05 AM
If all you have is the hdd that already has windows installed, and no cd or new hdd can this be done
Posted by: Rkidkool3 at November 28, 2008 8:52 AM
I have a related question and comment:
I agree - many times, if you just move your hard drive from one machine to another and boot up, it may likely fail.
My question is this: could it be done if all drives for the NEW machine are installed prior to moving the hard drive, will it work? And if it works, can you dual boot?
Posted by: David at May 1, 2009 1:12 AM
hi leo,
I am baout to replace my motherboard. At present I have windows7 installed in C and many other imp info
in the other hard disks. will all the information get erased when i replace my existing motherboard with a new one? if so is there any chance in which i can keep all my information as well as the OS intact?
thanks.
Backup everything first. It's possible that you will need to reinstall Windows.
01-Dec-2009
Posted by: Aravind at December 1, 2009 5:58 AM
ATTENTION!!! I just bought (Dec 1, 09) a brand new HP Pavillion and opened it up (was no warranty tape on it) to move my E drive from my old computer over (has all my pictures and music) and the new Hard Drive and Motherbord have a completely NEW setup! New style of cables, power and data for HDD, and no place on the motherboard to plug in the ribbon connector from my old HDD! Has a place for a floppy ribbon (34 pin block - FDD) but NOT a 40 pin IDE block! Don't understand their mentality (industry forcing everyone to buy new hard drives =$$$$ I suppose). My old Motherboard has a physical problem and wont run. I guess I can plug my old HDD into a friends computer and tranfer it all to a newly bought new style HDD(like to keep this data off the same HDD as my OS). Any way of using the 34 pin Floppy block? Is there a card I can plug into a PCI slot and connect to? Can my HDD be converted to an external drive that uses a USB or other connector? ***ANY thoughts or suggestion wouid be greatly appreciated***
Get yourself an external USB enclosure for the IDE drive - they're available at most places like Fry's or even Amazon. Cheap, and very flexible. New computers these days are using SATA drives, which are typically faster, though a different interface.
Comments
Read the article that everyone's commenting on.
Subscribe to the RSS Feed for comments on this article.
I have replaced motherboards and kept the hard drive many times over the years without any problems.
Well, one "minor" problem with an easy workaround. The first time you boot to Windows (assuming this is a Windows system, given the references to "C:" and "D:"), it will probably detect new hardware and will want to install new drivers off the Windows CD. Unfortunately, I have had motherboard upgrades where this "insert the Windows CD" prompt occurs _before_ the CD drivers are loaded, causing a nice Catch 22 situation.
To get around this, I make a "\windows.cd" directory on the hard drive, and copy the Windows install CD there _before_ installing the new motherboard. Then, simply tell the new hardware wizard to look there, rather than the CD drive itself.
Posted by: Ken at October 19, 2006 7:23 AMWell, some days before I have read something about copying windows registry, specially "\...\WAB", and "\system32" directory. After that I supposed was told to get some "merge program", and run it including these two situations. The issue was making ourselves a new computer and tranfer the windows serial to the new one, including hard disks and keep them ok. Might be good discoussing these options ? Something good to keep from this?
Posted by: Vic at October 22, 2006 7:20 PMVic
I've got a client that has had their mobo and cpu fried, so ive replaced both those, but here is where the problem lies, they did not back up their system and would like to keep everything the way it was on the old hdd without reformatting and losing all data and programs installed (as they do not have the original install files for these programs). My question is (as i know the old xp pro hdd will not boot with new system) i've already run the repair install and recovery console, but to no avail, it gets stuck un the boot loop like many others. But, i have built my own machine with the same system (mobo and cpu) with a clean xp pro install which does not have any programs or devices installed.... could i swap the start up files to the old hdd with the same mobo and cpu to get it started to detect all the new drivers and keep programs and data etc. and if so, what files would i need to replace on the old hdd from my clean hdd? (ive already tried everything i can think of and this popped into mind) btw, i cannot boot into safe mode on the old hdd to remove the drivers so windows will pick them up on repair for the new mobo. and the system when boots in safe mode will hang on 'gagp30kx.sys' which i assume is the video card? or failing that, how would i go about deleting the drivers that try to boot using recovery console. sorry for the long question, im just at that stage where ive been over and over with this thing for days and becoming a zombie. cheers and thanks in advance, pammii.
Posted by: pammii at October 31, 2006 5:42 PMLinux. Many distributions available, free for the price of downloading and burning it.
Posted by: Skandi Franksen at November 3, 2006 8:45 PMI swapped a SATA HD and Grafx card into a fully functional system. Windows would not go. Linux go'ed. Writing this while hunting down a way to make Windows go (for one game only, once I'm done with it I reformat and say goodbye to Windows on my personal boxes).
Why is it so easy to--and get this, hot plug a hard drive into your mobo--change hardware on other OSs while the leading OS supplier's software costs so many man-hours to change? Motherboards' lifespans are finite--not that they die, always, but c'mon, the technology changes.
Hi Leo, My, Motherboard has failed me, and I have important data on my HDD(which has windowsxp installed), when I put it in another computer, it just makes a blinking sound and I get the message 'Cannot read HDD'. Is there anything I can do to use this HDD again?
Posted by: dave at November 8, 2006 4:21 AMA local competent builder is assembling a new machine for me. New: motherboard; new boxed version XPpro; new HD. Old: XPpro; 2 HD; several Autocad,Catia & Solidworks programs. How to transfer to the new machine? I realize this is already partially answered in your column but the "devil" is in the details! Specific questions are best when all details are given. Some friends advise Magic Mover. That seems to out of date. I am in no hurry to lose programs. This seems to be a common task, as 2 other of this builder's customer's are attempting to do the same task. Also I have no agreement on partitioning of the new HD. How many partitions of what size? I have about 20 gig of cad type programs now.
Posted by: arlie at July 2, 2007 10:05 AMIf all you have is the hdd that already has windows installed, and no cd or new hdd can this be done
Posted by: Rkidkool3 at November 28, 2008 8:52 AMI have a related question and comment:
I agree - many times, if you just move your hard drive from one machine to another and boot up, it may likely fail.
My question is this: could it be done if all drives for the NEW machine are installed prior to moving the hard drive, will it work? And if it works, can you dual boot?
Posted by: David at May 1, 2009 1:12 AMhi leo,
I am baout to replace my motherboard. At present I have windows7 installed in C and many other imp info
in the other hard disks. will all the information get erased when i replace my existing motherboard with a new one? if so is there any chance in which i can keep all my information as well as the OS intact?
thanks.
01-Dec-2009
Posted by: Aravind at December 1, 2009 5:58 AM
ATTENTION!!! I just bought (Dec 1, 09) a brand new HP Pavillion and opened it up (was no warranty tape on it) to move my E drive from my old computer over (has all my pictures and music) and the new Hard Drive and Motherbord have a completely NEW setup! New style of cables, power and data for HDD, and no place on the motherboard to plug in the ribbon connector from my old HDD! Has a place for a floppy ribbon (34 pin block - FDD) but NOT a 40 pin IDE block! Don't understand their mentality (industry forcing everyone to buy new hard drives =$$$$ I suppose). My old Motherboard has a physical problem and wont run. I guess I can plug my old HDD into a friends computer and tranfer it all to a newly bought new style HDD(like to keep this data off the same HDD as my OS). Any way of using the 34 pin Floppy block? Is there a card I can plug into a PCI slot and connect to? Can my HDD be converted to an external drive that uses a USB or other connector? ***ANY thoughts or suggestion wouid be greatly appreciated***
03-Dec-2009
Posted by: Sage at December 2, 2009 8:30 AM
To post a comment on "Can I use my old hard drives with a new motherboard?", please return to that article's main page.